Davis DriveRight 600E Users Guide (8126, 8179) Manual de usuario

km/hMPHSPEEDDISTANCEMILESKmSETTINGSSpeed ReadingDistance Reading Calibration Speed6Calibrating the DriveRight 600ECalibration Screen4. Drive the vehic

7Calibrating the DriveRight 600EBe aware that the DriveRight 600E responds to changes in speed faster than most vehicles’ speedometers. To accurately

8Data Screens5. When finished driving, compare the vehicle’s distance reading to the distance reading on the DriveRight 600E.6. Increase or decrease t

9Data ScreensCurrent Readings ScreenThe Current Readings Screen display is constantly updating (when the vehicle is moving) speed, distance (for the c

10Data ScreensNote: Although trip type can be specified using the DriveRight 600E display device, FMS must be used to view the trip type for each trip

11Data ScreensNote: Driver ID code 0000 (four zeros) is used to view information for the vehicle (all drivers) and should not be assigned to any driv

12Data ScreensCode Entry Screen. To view all trip times for the vehicle, enter ID code 0000.Note: If the end time for a trip is “dashed,” it means tha

km/hSPEEDOVERTIMESPEEDSec.DISTANCEKmLOGMaximum Speed During Trip DateDistance TraveledDuring TripAmount of Time Spent Driving Over Set Speed Limit Dur

14Data ScreensThe following options are available in the Trip Acceleration/Decelera-tion Log Screen:• Page Through Stored Trip Information — Press MIN

15Settings ScreensA “NO” on the Latitude and Longitude Screens indicates the GPS mod-ule is not able to track your current position. The last known po

© Davis Instruments Corp. 2007. All rights reserved.DriveRight 600E User’s Guide Rev. B, 5/31/07Document Part Number: 7395.225Product Numbers: 8126GD

16Settings Screens• Move to the next Settings Screen — Press and release MODE.• View the Data Screens — Press and hold MODE.Security Code ScreenIf you

17Settings Screens• Set or Change the Security Code — Use PLUS and MINUS to enter the current correct code, if entering the security code for the firs

CLEAR LOGSETTINGS18Settings ScreensPreparing to Clear Log DataContinue to hold SET/CLEAR until the DriveRight 600E beeps and “CLR” disappears from the

19Settings ScreensTime EntryThe Time Entry Screen enables you to set the time and to select the format (12-hour or 24-hour) in which you want time dis

20Miscellaneous Information• Set the Date — Press PLUS and MINUS to toggle through the numbers for each segment. Press SET/CLEAR to move through each

21Miscellaneous Information• DriveRight 600E is manually rebooted.When a tamper is logged, “TAMPER” displays on all screens if the tamper light has be

22Miscellaneous InformationTo install a new battery, insert the battery as shown below.Installing the BatteryA low battery can be replaced without los

23Troubleshooting GuideBattery LifeWhen removed from a vehicle, the DriveRight 600E taps into its own battery for power (instead of relying on the veh

24Troubleshooting Guide(www.davisnet.com) or send an e-mail to tech support ([email protected]).Note: Please do not return your DriveRight 600E for

25Troubleshooting Guide• The speed reading on the DriveRight 600E agrees with my vehicle’s speedometer, but the distance reading on the DriveRight 600

iTable of ContentsIntroduction to the DriveRight 600E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A Note About the Concept of “

26Technical SpecificationsTechnical SpecificationsCheck our website for updated specifications: www.davisnet.com.GeneralSensor Type. . . . . . . . . .

27Technical SpecificationsSpeedDisplay: . . . . . . . . . . . . . . . . . . . . . . . Current speed in mph or km/h. Records maximum speed for each tr

28Contacting Davis Technical SupportIf you have questions, or encounter problems installing or operating your DriveRight 600E, please contact Davis Te

ii

1Introduction to the DriveRight 600EThe DriveRight 600E, in conjunction with DriveRight Fleet Manage-ment Software (FMS), provides advanced vehicle sa

2Using the DriveRight 600EUsing the DriveRight 600EThis section briefly describes the DriveRight 600E display, the use of the four buttons (PLUS, MINU

3DriveRight 600E ScreensData ScreensThe Data Screens display most of the information stored in the DriveRight 600E device. To cycle through the Data S

4Calibrating the DriveRight 600ENote: To exit the Settings Screens and view the Data Screens, press and hold MODE until the Current Readings Screen di

5Calibrating the DriveRight 600Efrom the DriveRight 600E’s default of 4000 pulses per mile, or if the vehicle’s pulses per mile are not known. VSS ver