DAVIS Rain Collector Shelf Manual de instalación

Busca en linea o descarga Manual de instalación para Lavadoras DAVIS Rain Collector Shelf. DAVIS Rain Collector Shelf Installation manual Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 8
  • Tabla de contenidos
  • SOLUCIÓN DE PROBLEMAS
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Davis Instruments, 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. • 510-732-9229 • www.davisnet.com
®
Rain Collector II
Installation manual
This instruction manual takes you step-by-
step through the procedures required to
install the Rain Collector II. The Rain
Collector II is designed for use with any of
Davis’ Vantage Pro2 weather stations, including
the Anemometer/Sensor Transmitter Kit.
Note: If you are installing the Rain Collector II in a Weather Wizard or Weather Monitor, please refer
to the Rain Collector II for GroWeather, EnviroMonitor, Weather Monitor and Wizard manual
which can be found in the support section of the Davis web site. (Go to www.davisnet.com,
click Support, Weather Support, Instruction Manuals. Choose your station from the pull down
menu and scroll down to find the manual.)
Components
The Rain Collector II includes the following components. Please make sure you have
all listed components before continuing.
Rain Collector with Cable — The rain collector comes with the cone attached to the
base and has a 40’ (12m) cable.
Four #8 x 3/4" Screws
Debris Screen — This screen is placed into the rain collector cone to help prevent
debris from clogging the funnel hole.
Metric Rain Adapter — This adapter adds weight to the tipping mechanism, adjusting
it to tip for every 0.2 mm of rainfall instead of every 0.01”.
Tools and Materials Needed
You may need some of the following tools and materials to install the rain collector.
Drill with 3/32” (2 mm) drill bit
Medium Phillips screwdriver
3/16” (or 5 mm) wrench
Cable clips or weather-resistant cable ties with screw holes or other means for mount-
ing
Bubble level
Vista de pagina 0
1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Rain Collector II

Davis Instruments, 3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A. • 510-732-9229 • www.davisnet.com® Rain Collector IIInstallation manualThis in

Pagina 2 - Components

Components2Rain Collector Internal ComponentsThe illustration below shows the internal components of the rain collector, many of which are referenced

Pagina 3 - Prepare the Rain Collector

Prepare the Rain Collector3Prepare the Rain Collector1. Turn the rain collector upside down and remove the cone from the base by rotating the base unt

Pagina 4 - Install the Rain Collector II

Test the Rain Collector II43. Separate an end cap from one side of the magnet.4. Slide the magnet, with the exposed end of the magnet first, into the

Pagina 5

Install the Rain Collector II5Choosing a Location for the Rain CollectorKeep the following in mind when choosing a location for your rain collector:•Y

Pagina 6 - Extending Cable Runs

Adjusting the Rain Collector II66. Open the SIM housing on the ISS. Remove the foam insert and feed the rain collector cable up through the opening. P

Pagina 7 - Troubleshooting Guide

Maintaining the Rain Collector II7change. Moving the screws in the positive (+) direction causes the bucket to tip more times (i.e. give a larger coun

Pagina 8 - Specifications

Product Number: 7852 Part Number: 07395.275 Rain Collector II Rev A (1/24/12)This product complies with the essential protection requirement

Comentarios a estos manuales

Sin comentarios